This product record identifies a liner, part number T3135X062, in the Lovol Excavator category. It does not identify the engine family, bore size, liner type, protrusion, material, or serial-number application. Those are essential fitment facts and should not be inferred from the photograph. Use the part number as a catalog clue, then confirm the engine code and the exact liner specification in the service parts book before purchasing or beginning a rebuild.
Why liner identity matters during an engine overhaul
A cylinder liner provides a controlled running surface for the piston and rings in engines designed around a replaceable liner. The liner’s dimensions, seating arrangement, cooling or sealing features, and relationship to the block depend on the engine design. A liner with the wrong bore or height can affect clearances, sealing, compression, or assembly. This listing gives no dimensional data, so it is not a measurement reference. Always compare the proposed item against the engine manual and the removed part.
Wear, scoring, corrosion, glazing, or abnormal oil consumption may lead a workshop to inspect a liner, but those conditions need diagnosis in context. Piston, ring, cooling, lubrication, and air filtration condition can contribute to the same symptoms. Before ordering, record what was observed and whether the engine is being dismantled for planned overhaul or a specific repair. That context helps a parts supplier ask whether related seals, rings, or fasteners are also needed, without assuming they are included here.
Confirming T3135X062 against the engine
Read the engine identification plate and capture the complete engine model and serial number. Check the parts illustration for the specific cylinder block and liner position. Confirm whether the design uses a wet or dry liner, but only from authoritative engine information; the current record does not state which type applies. Check any serial-number break or supersession note, and confirm whether the number is for one liner or an assembly. Package quantities should not be guessed from a singular product title.
If an old liner is available, preserve identification marks and inspect its features before cleaning. Record overall length, bore, flange or seating geometry, locating features, and any grooves or ports only as comparison data. Use calibrated measuring equipment and the manual’s tolerances for actual inspection. A worn liner may no longer represent its original dimensions. Photograph the part with a scale and note the cylinder location; never use a visual estimate as an approved bore measurement.
Clean teardown and inspection practice
Engine overhaul should be conducted by qualified personnel in a clean, organized work area. Isolate the machine, allow components to cool, and follow the engine manufacturer’s safety process. Mark pistons, rods, caps, and liners by cylinder before removal so they cannot be mixed. Keep open oil and coolant passages protected. If contamination enters the block, it can damage components after reassembly, so clean handling is part of the repair rather than a cosmetic step.
After removal, inspect the block bore and liner seat for corrosion, erosion, cracks, debris, and damage. Check the condition of any liner seals or sealing lands specified by the design. Do not scrape precision surfaces with hard tools or apply sealant unless the procedure calls for it. A damaged block seat or out-of-round bore may require specialist measurement or machining; a replacement liner alone cannot correct every underlying condition.
Use the prescribed installation method, support tools, and lubrication for the identified engine. Do not force a liner into place or polish surfaces to make a mismatch fit. Confirm orientation and seating height using the correct measurement method and limits. If the manual calls for replacement of seals, shims, or related parts, identify and order those items separately unless a supplier confirms a kit is included.
Assembly and checks after installation
Before installing the piston assembly, verify liner installation and all required measurements against the service manual. Keep the bore clean and protect it from scratches. Install rings and pistons using the correct orientation, ring-gap arrangement, and tools for the engine. Values for clearance, protrusion, torque, and ring gap are not supplied in this product record; consult the engine documentation rather than using generic figures.
After reassembly, follow the machine-specific priming, fluid filling, and commissioning process. Confirm that oil and coolant levels, connections, and monitoring systems are ready before starting. Observe the engine under controlled conditions and follow the recommended break-in or load procedure, if specified. If unusual noise, leakage, smoke, overheating, or pressure warnings appear, stop and investigate immediately. A successful parts match must be accompanied by correct machining, assembly, and commissioning.
Useful details for a liner quotation
Send part number T3135X062, both machine and engine identification plates, engine serial number, cylinder position, and the relevant parts-diagram reference. Include photographs of the removed liner’s ends and any markings. State whether measurements were taken and who verified them; attach the measurement sheet if available. Ask the supplier to confirm the liner type and included quantity in writing. This avoids relying on assumptions about engine configuration or packaging.
For an engine parts enquiry, organize this liner separately from valve and bearing requirements. The intake valve T3142L072 reference and main bearing T81558 listing are separate parts; each requires its own engine and serial check.
Frequently asked questions
Does T3135X062 state the liner bore size?
No bore or dimensional specification is listed here. Confirm the engine code and exact measurements through the approved parts and service information.
Can I identify wet or dry construction from the listing?
No. The listing does not provide liner type. Use the engine parts manual or ask a qualified parts specialist to verify it for the identified serial range.
Should the old liner be reused if there is no obvious crack?
Make that decision only after inspection and measurement against the engine manufacturer’s limits. Visual appearance alone cannot establish serviceability.
What should be supplied with an enquiry?
Provide the full engine and machine identification, serial number, part number, cylinder position, diagram reference, and clear photos or verified measurements.
Catalog summary
| Catalog item | Liner |
|---|---|
| Part number | T3135X062 |
| Category | Lovol Excavator |
| Engine fitment and dimensions | Not stated; confirm by engine serial and approved specifications |
Careful liner sourcing links the right catalog reference with measured engine data, clean workmanship, and an approved assembly process. Use this page to start the inquiry and verify the application before a rebuild is scheduled.