Description

This catalog entry identifies a half axle gear gasket with part number B00256+75201604 in the Lovol Excavator category. The title points to a sealing gasket associated with a half-axle gear assembly, but the record does not specify the mating case, material, thickness, bolt pattern, dimensions, or machine serial range. Those missing details are important: a gasket must match the actual joint surface and assembly, not simply the broad component name. Treat the number and original sample as the basis for confirmation.

What a gasket contributes at an assembled joint

A gasket sits between two mating surfaces to help maintain the intended seal when the joint is assembled to the prescribed condition. Its outline, holes, cut-outs, material, and thickness all affect whether it fits and performs as intended. If the gasket is too small, a passage may be obstructed or a sealing edge may not be covered. If it is too large, it can interfere with nearby features. A wrong thickness can alter the assembled clearance or position, depending on the design. None of these dimensions are published in this catalog entry, so they must be checked against the parts book or removed part.

During a half-axle or gear-area repair, the joint may be opened to inspect a leak, replace a component, or restore an assembly after service. The exact location and lubricant are machine specific. Do not assume from the product name alone whether this gasket seals a final-drive housing, axle carrier, or another joint. The service illustration and machine serial number settle that question. If an old gasket has been torn during removal, retain all pieces and photograph their orientation before cleaning the joint.

Identifying part B00256+75201604

Copy the part number exactly as printed, including the plus sign. Some inventory systems treat punctuation as significant, and omitting a character can lead to a different catalog result. Compare the number in the relevant parts diagram with the machine plate and the revision information, if shown. If the diagram calls out a gasket as part of a kit, clarify whether this listing is the individual gasket or a kit component; the current record names one gasket and does not state included quantities.

When no readable number remains on the old part, use a measured trace only as supporting evidence. Place the sample on a flat surface without stretching it. Record the outer dimensions, hole centres, passage openings, orientation marks, and any tabs. A photograph with a ruler in the same plane helps a supplier compare shapes, but it cannot replace the manufacturer’s part reference. Avoid measuring a compressed, swollen, or badly damaged gasket as if it were an original specification.

Preparing the mating surfaces

Before disassembly, stabilize the machine, lower the work equipment, isolate it according to the service procedure, and keep the work area clean. Support components that could shift when fasteners are removed. Capture photographs of the assembly and note the orientation of each part. Drain or contain any lubricant only as the manual directs. Keep open housings protected from dust, grit, and loose fasteners.

Once separated, remove remnants with a method approved for the housing material. Avoid gouging the sealing face with a screwdriver or abrasive tool. A scratch crossing the sealing path can create a leak even when the replacement gasket is correct. Clean the joint and inspect it under good lighting for corrosion, dents, raised burrs, cracks, or distortion. If a surface is damaged or uneven, the repair requires an appropriate assessment; a thicker sealant layer is not an automatic remedy.

Use only the sealing compound or dry-install method specified by the machine documentation. Some gasket designs are installed without additional sealant, while others prescribe a particular product and application location. Applying compound indiscriminately can squeeze material into oil passages or change the joint’s effective thickness. Do not reuse a gasket that the service procedure requires to be replaced after separation.

Installation and post-repair checks

Compare the replacement with the old gasket before assembly: perimeter, holes, notches, orientation, and material appearance. Confirm that the gasket lies flat and does not cover a passage or hang into the housing. Bring the joint together without sliding or pinching the seal. Tighten fasteners in the sequence and to the values specified for the machine; this listing provides no torque information. Uneven tightening can distort parts or load the gasket incorrectly.

After reassembly, refill or check lubricant only to the prescribed specification and level. Follow any inspection or run-in procedure in the service manual. Observe the joint for leakage under the controlled conditions stated there, and recheck surrounding fasteners only if the manufacturer instructs it. If a leak remains, investigate surface condition, assembly alignment, and the correct gasket identity rather than simply tightening beyond specification.

How to request a confident quotation

Send part number B00256+75201604, the machine identification plate, the relevant parts-diagram reference, and a clear image of the old gasket beside a ruler. Include the joint location as named in the manual and explain whether the gasket came from a scheduled teardown or a repair inspection. If the machine has a serial-number split, include the full serial range. This lets the supplier verify the catalog reference and ask about dimensions or revision differences before dispatch.

Keep related components separately identified in the work order. For example, this seal should not be confused with a shaft or engine bearing. See the lower joint shaft catalog record and the main bearing listing as separate items that may appear in a broader repair enquiry.

Frequently asked questions

Does the listing show gasket dimensions or material?

No dimensions, thickness, or material specification are stated here. Confirm those details through the machine’s parts documentation and the original component.

Can I reuse the old gasket if it looks intact?

Follow the manufacturer’s service instructions. Many joints call for replacement once opened; visual appearance alone does not prove that a compressed gasket will seal again.

Should sealant always be applied?

No. Use only the sealing method specified for the joint. Excess or incorrect compound may interfere with passages or alter assembly conditions.

What information helps verify the part?

Provide the complete number including its plus sign, machine serial, diagram reference, joint location, and a clear photo of the old gasket with its outline and openings visible.

Catalog summary

Catalog nameHalf axle gear gasket
Part numberB00256+75201604
CategoryLovol Excavator
Fitment and dimensionsNot stated; verify by serial number, diagram and original gasket

A careful match protects the sealing faces and avoids reopening the joint to correct a preventable mismatch. Use the catalog number to start the enquiry, then confirm the actual housing and service procedure before fitting.

FREE Inquiry Now

If you have any questions, feedback or comments, please fill out the form below and we will reply you back as soon as possible.

+86-130-4508-1859

Get A Quote