This catalog entry identifies a main bearing with part number T81558 and places it in the Lovol Excavator category. It does not publish the engine code, bearing position, size grade, material, dimensions, clearance, or compatible serial ranges. Main bearings are selected to match a specific crankshaft and block specification, so a short number and a generic name are not enough to choose a size. Confirm the application in the engine parts documentation and verify measured clearances using the approved service procedure.
Understanding the role of a main bearing
Main bearings support the crankshaft at its main journals and help maintain the designed running clearance and oil film. Their condition influences crankshaft support and lubrication. During an overhaul, a technician may inspect bearings for scoring, wear, discoloration, embedded debris, or uneven contact. Those findings should be considered with crankshaft journal measurements, oil-system condition, block alignment, and operating history. A bearing marked T81558 should not be assumed to fit every engine in the broader equipment category.
Many engines use selection grades, undersize options, position-specific shells, or paired upper and lower halves. This listing does not state which configuration applies. Do not infer that the item is a complete set, a standard size, or suitable for a reground crankshaft. Those distinctions must be confirmed using the engine model, serial number, crankshaft measurements, and the relevant parts list. Ordering on appearance alone can create excessive or insufficient clearance and serious engine damage.
Identification steps for T81558
Read the machine and engine plates before the engine is dismantled. Capture the complete engine model and serial, and note any replacement or rebuild history. Locate the main-bearing callout in the correct parts diagram and check whether the number changes by position or serial break. Preserve the original packaging or bearing markings if available. If the engine has been rebuilt, ask which crankshaft size and bearing grade were installed rather than relying on the original machine configuration.
During teardown, label each shell by journal position and orientation. Keep upper and lower halves separate. Photograph their backs and running surfaces, including any stamped markings. Avoid polishing away identification. Record the crankshaft journal diameter at the positions prescribed by the manual, and inspect for taper, out-of-round, scoring, or cracks using approved tools. A used bearing’s dimensions may reflect wear and are not a reference specification.
Clean measurement and inspection practice
Main-bearing work demands meticulous cleanliness. Keep lint, grit, and abrasive residue away from the block, crankshaft, oil passages, and new shells. Clean components by the method recommended for the engine, then verify that oil galleries are clear. Do not use an abrasive pad on a precision journal without approval. A small particle trapped behind a shell can alter its seating and distort the clearance.
Inspect the block saddles, caps, locating tangs, and crankshaft surfaces. Check for fretting, damage, distortion, or evidence of overheating. A qualified engine technician should measure journals and bearing clearances with the specified tools and interpret the results using the engine’s limits. This catalog record provides none of those values. If a cap is damaged or main bore alignment is questionable, seek specialist measurement and correction instead of installing a new bearing over an unresolved problem.
Use the assembly lubricant, dry-fit method, shell orientation, and cap tightening sequence specified by the manufacturer. Never file a bearing shell or modify its locating feature to make it fit. Do not interchange caps or shells unless the engine procedure explicitly allows it. A replacement should sit correctly in its saddle with the locating features aligned and oil holes unobstructed.
Assembly and commissioning considerations
Before the crankshaft is installed, verify the bearing identity, position, grade, and clearance for the engine. Follow the manual’s procedure for measuring clearance and applying fastener torque or angle. Values differ by design and are not stated here. Rotate the crankshaft as instructed to confirm smooth movement and check end play where required. If resistance or binding is found, stop and recheck cleanliness, cap position, bearing grade, and measurements.
After completing the engine build, prime the lubrication system using the prescribed procedure before starting. Confirm oil level, filter, galleries, and monitoring systems. Start and load the engine only according to the commissioning instructions. Watch for oil-pressure warnings, unusual knocking, or leakage. Stop immediately if a warning occurs. The replacement bearing can only work correctly as part of a clean, measured, properly assembled lubrication system.
Information for a main-bearing enquiry
Provide part number T81558, machine and engine plate photographs, serial number, relevant diagram callout, bearing position, and the crankshaft size or grade confirmed during overhaul. State whether the crankshaft is standard or has been machined, and attach the measurement record if available. Ask the supplier to clarify the supplied quantity, upper/lower configuration, and grade before payment. These details prevent ambiguity about whether a single shell or a matching set is being quoted.
Keep this engine item distinct from other overhaul parts. The T3135X062 liner listing and the T3142L072 intake valve record may appear in a related engine enquiry, but each has separate identification and measurement requirements.
Frequently asked questions
Does T81558 tell me the bearing size?
The record does not state size, grade, journal position, or clearance. Confirm the engine configuration and measurements from the approved service documentation.
Is this listing a full main-bearing set?
The listing names a main bearing but does not state the quantity or package contents. Ask for written confirmation based on the engine and required positions.
Can I order the original size after a crankshaft grind?
Do not assume so. The selected bearing must match the measured crankshaft and engine specification after machining; verify the correct grade with the engine builder.
What should be checked before installation?
Confirm cleanliness, bearing position and grade, journal measurements, oil-hole alignment, specified clearance, and cap procedure. Use the engine manual for all limits and tightening values.
Catalog summary
| Catalog item | Main bearing |
|---|---|
| Part number | T81558 |
| Category | Lovol Excavator |
| Grade and application | Not stated; confirm engine, journal position and measured size |
Correct main-bearing supply depends on evidence from the engine, not just a generic description. Verify the serial, crankshaft measurements, size grade, and package contents before scheduling assembly.