This catalog record identifies an oil pump, part number T4132F056C, and categorizes it under Lovol Excavator. It does not provide an engine code, displacement, pump type, flow, pressure, dimensions, drive arrangement, or serial-number coverage. “Oil pump” is a broad name: the correct unit depends on the engine and lubrication-system design. Confirm the exact application and pump configuration in the relevant engine parts list before ordering; do not choose by exterior resemblance alone.
The oil pump’s role in the lubrication circuit
An engine oil pump moves lubricant through the circuit so bearings and other specified surfaces receive oil under the conditions intended by the manufacturer. The pump works with the pickup, strainer, relief arrangement, galleries, filter, and oil grade. A warning light, low indicated pressure, unusual engine noise, or oil leakage can have several causes. These signs do not prove that the pump itself has failed. The service procedure should verify oil level, sensor function, filter condition, pickup restriction, leakage, and pressure using the correct test point and instruments.
A replacement pump must match the engine’s drive, mounting, internal configuration, and oil-path interfaces. A similar housing can conceal differences in gears, rotor, relief components, passages, or drive orientation. This record does not list those details. Use the engine plate, serial number, parts diagram, and any revision note. If a machine has had an engine replacement, identify the installed engine rather than relying only on the chassis model.
Verifying part T4132F056C
Copy the number exactly, including the final letter. Compare it with the callout for the identified engine and confirm whether the record is for a complete pump or an individual component. The listing does not state package contents, seals, pickup tube, or drive gear. If a supplier quotes a kit, request a written breakdown of included parts. A photo of the existing pump’s label, mounting face, ports, and drive can support identification, but the parts manual remains the primary reference.
Before removal, document the pump’s orientation and the path of connected components. Capture the pickup and any screens, mounting bolts, gaskets, and drive interface. Preserve marks and do not disassemble the pump unless the engine procedure requires it. If the pump is damaged, record how it failed and inspect the lubrication system for debris. Metal particles or sludge may affect other components and should be addressed according to the manufacturer’s cleaning and inspection process.
Diagnosis before replacement
Confirm oil level and the specified oil grade first. Check for external leakage, a blocked pickup, a damaged strainer, incorrect filter, aeration, or a faulty pressure sensor using the proper diagnostic steps. If pressure must be measured, use the specified equipment, location, temperature, and engine condition. Generic pressure values can mislead; this listing supplies no test limits. Avoid extended operation when a lubrication warning is active or abnormal mechanical noise is present.
When the pump is removed, inspect drive features and mounting surfaces for damage. Check the pickup tube and seals as appropriate. The reason for low pressure may lie elsewhere, including excessive bearing clearance, worn journals, an open relief path, or a restriction. A new pump cannot correct every lubrication fault. A qualified engine technician should interpret inspection results and decide whether additional repairs are required.
Installation and clean assembly
Work on a cool, isolated engine in a clean area. Drain oil and protect open passages. Keep lint, abrasive residue, and loose hardware out of the crankcase. Clean mounting faces without gouging them. Compare the replacement number, drive, mounting points, and oil passages with the approved reference. Install new seals or gaskets only as specified, and do not apply excess sealant where it could enter the oil circuit.
Prime or pre-lubricate the pump only by the engine manufacturer’s method. Follow the prescribed fastener sequence and torque from the service manual; values are not stated in this catalog. Reconnect the pickup and associated parts with clean components. Ensure no line or fitting is stressed or left loose. Refill with the correct oil and filter, then prime the lubrication system before startup if the procedure calls for it.
Commissioning and maintenance records
Start and inspect the engine under controlled conditions. Confirm that oil pressure responds as expected according to the engine documentation, and check for leaks or unusual noise. If pressure does not establish promptly or a warning remains, stop the engine and investigate. Do not increase speed to force pressure or continue work in the hope that the issue will clear. Complete the prescribed follow-up inspection and record the engine hours, oil and filter details, part number, and any measurements.
For a fleet workshop, retain the old pump and documented findings until the repair is verified. A concise record helps later technicians distinguish a recurring pump problem from contamination or a broader engine wear issue. If debris was found, note the source investigation and cleaning steps. Follow the manufacturer’s interval for oil and filter service rather than substituting a generic schedule.
Information for an oil-pump quotation
Send part number T4132F056C, engine plate and serial, machine identification, diagram reference, and photographs of the existing pump. State whether the engine is original to the machine and explain the diagnostic evidence that prompted replacement. Ask whether the quoted part includes seals, drive components, or any related items. Confirm supersessions and fitment in writing before arranging shipment.
Keep this pump distinct from the oil return filter 9F850-58A050000A0 and the main bearing T81558. Those separate catalog entries relate to different components and require their own engine and system verification.
Frequently asked questions
Does T4132F056C state the engine application?
No engine model or serial range is given here. Confirm the part number against the installed engine’s parts book.
Can low oil pressure be assumed to mean pump failure?
No. Check the complete lubrication system and verify pressure with the approved procedure before deciding which component to replace.
Are seals or a pickup included?
Package contents are not stated. Ask the supplier to confirm each included component before purchase.
What should be checked after fitting?
Follow the specified priming and start-up process, verify pressure under the approved conditions, inspect for leaks, and stop if warnings or abnormal noise remain.
Catalog summary
| Catalog item | Oil pump |
|---|---|
| Part number | T4132F056C |
| Category | Lovol Excavator |
| Engine specification | Not stated; verify engine code, serial and lubrication-system design |
Oil-pump sourcing should follow a confirmed diagnosis and a precise engine match. Use the number as a starting reference, then validate the installed engine, pump configuration, and repair procedure before assembly.