This product listing identifies a piston cooling jet with part number T3861A027 and category Lovol Excavator. It does not state the engine family, nozzle pattern, flow specification, mounting method, dimensions, or serial-range fitment. A cooling jet is a precision component in an engine’s lubrication arrangement, and an apparently similar nozzle may have a different orientation or discharge pattern. Confirm the engine code and parts-diagram callout before ordering; do not treat the image or name as a complete technical specification.
What a piston cooling jet does
In engines designed with piston cooling jets, the component directs oil toward a specified area of the piston to help manage temperature and lubrication. Its performance depends on the engine’s oil supply, nozzle geometry, mounting position, and clearance to moving components. A damaged, blocked, loose, or incorrectly oriented jet can affect the intended oil delivery. The exact design varies, so this page does not publish a flow rate, pressure, or spray pattern. Those values and the installation orientation must come from the engine documentation.
Engine symptoms such as elevated temperature, unusual piston wear, oil-pressure concerns, or debris can have many causes. They do not by themselves establish that the cooling jet is faulty. A technician should assess oil condition, pump supply, galleries, clearances, piston condition, and the relevant engine measurements. This part should be inspected during an approved repair or overhaul rather than removed as a trial adjustment without the manufacturer’s procedure.
Identify T3861A027 against the engine
Start with the machine and engine identification plates and the serial number of the installed engine. Locate the jet in the correct exploded view and check its position, quantity, and any revision notes. If the engine has been replaced, use its actual code instead of the machine model alone. Copy T3861A027 exactly and ask the supplier to confirm whether it is a single jet or part of a larger assembly. The listing does not specify package quantity or included fasteners.
If an old jet is available, photograph its mounting face, orifice, locating features, and any markings before cleaning. Do not insert a wire or drill bit into the orifice; altering its diameter can change oil delivery. Use only the cleaning method prescribed by the engine maker. Compare orientation and mounting details with the approved drawing. A visual resemblance is useful for screening but is not a final fitment confirmation.
Inspection during engine service
Before opening the engine, make the machine safe, isolate energy sources, and allow it to cool. Engine internal repairs require qualified personnel and clean workshop practices. Protect oil galleries from dust and loose hardware. Keep removed components arranged by cylinder or location, and label their original positions. If an oil jet is removed, record its orientation and the reason for inspection. Avoid mixing similar-looking nozzles from different positions or engines.
Inspect the nozzle and attachment for impact damage, bending, cracks, blockage, looseness, or deformation. Check the corresponding passage and mounting surface as directed by the service manual. Look for evidence of contamination or wear in the lubrication system. Do not assume that a visible clean orifice proves the jet meets specification; flow and orientation checks must follow the approved test method. If the orifice is damaged or the part has been modified, replace it only with the confirmed reference.
Clean surrounding areas before removal so debris does not enter the crankcase. Use lint-free materials and approved cleaning fluid. Do not direct high-pressure air into a passage unless the procedure specifies safe handling; particles can be propelled into sensitive areas. If metal debris or sludge is present, document it and follow the engine’s contamination investigation and cleaning process before reassembly.
Installation and clearance verification
Before installing a replacement, verify T3861A027, its engine application, and position in the drawing. Ensure the jet is oriented as specified and its mounting surface is clean. Use the required fastener, locking method, seal, and tightening procedure stated by the engine manufacturer. This product entry gives no torque value. Do not bend the nozzle to alter its aim and do not substitute a generic fitting. Confirm clearance to the piston and crank components by the prescribed method before closing the engine.
Once installed, verify that the lubrication path is unobstructed and that the pump, filter, and oil passages are assembled correctly. Prime the system as the engine procedure directs. Use the specified oil grade and fill level. Before starting, complete required hand-rotation, clearance, and inspection checks. After start-up, monitor oil pressure, leaks, and abnormal noises under controlled conditions. Stop the engine if a warning persists or any unusual behavior appears.
Build an accurate parts enquiry
For a quotation, send part number T3861A027, machine and engine plates, full engine serial, diagram reference, cylinder position, and photographs of the removed jet. Explain whether the enquiry is for a planned overhaul or a diagnosed failure, and ask the supplier to confirm quantity, package contents, and any applicable supersession. If your workshop has recorded dimensions or a test result, include the method and source of the measurement. This helps keep the discussion tied to the actual engine rather than assumptions based on a short description.
For related engine overhaul references, see the oil pump T4132F056C listing and the engine liner T3135X062 record. They are distinct products; verify each part number and the engine configuration independently.
Frequently asked questions
Does this record provide the oil-jet flow rate?
No flow, pressure, or spray specification is stated. Consult the exact engine service information for required values and tests.
Can I clear a blocked nozzle by enlarging the opening?
No. Do not alter the calibrated opening. Follow the approved cleaning procedure or replace the part with a verified reference if it is damaged or blocked.
Does the listing confirm which engine uses T3861A027?
The record supplies a category and part number but no engine application table. Confirm the code and serial range using the machine’s engine parts book.
What should be checked before the engine is closed?
Verify part identity, nozzle orientation, mounting security, passage cleanliness, and clearance using the specified procedure. Complete all lubrication-system checks before commissioning.
Catalog summary
| Catalog item | Piston cooling jet |
|---|---|
| Part number | T3861A027 |
| Category | Lovol Excavator |
| Engine and flow details | Not stated; verify with engine code, serial and service specifications |
Accurate engine identification, careful handling, and correct assembly determine whether this small component matches the intended lubrication design. Use the number to begin the inquiry, and confirm its application and installation details from the proper service documentation before repair.