This record identifies a planet gear gasket, part number B00256+75201605, under the Lovol Excavator category. The listing does not specify its exact joint location, profile, material, thickness, gear carrier assembly, or machine serial range. A gasket associated with a planetary gear assembly must be matched to the correct housing interface and drawing callout. Do not infer that it fits every final drive or axle simply because the component name includes “planet gear.” Confirm the part number and assembly in the machine’s parts book.
Why a planetary assembly gasket needs exact matching
Gear assemblies often use closely fitted housings, covers, carriers, or other interfaces. A gasket’s outline, holes, passages, and thickness must correspond to the actual joint. If the outline is wrong, it may leave a sealing edge uncovered or obstruct a passage. If thickness differs from the design, it may change the assembled relationship or clearances. The catalog does not publish these dimensions or identify the exact mating parts, so verify them from the parts illustration and the removed sample.
During repair, the assembly may be opened for inspection, leakage correction, or replacement of gears or bearings. The lubricant and joint are machine specific. Do not assume which housing this gasket seals, or what fluid passes through it, based only on the name. Use the serial-specific diagram, label the assembly position, and capture the orientation before disassembly. Keep every removed piece so a torn gasket can still be compared to the mating surfaces and passage pattern.
Confirming B00256+75201605
Enter the part number exactly, including the plus sign and all digits. Compare it with the relevant callout and any serial break or supersession shown in the manufacturer’s records. The plus sign may be meaningful in the catalog search. Ask whether the listing is for one gasket or a kit, because package quantity is not stated here. If other seals or fasteners are needed, identify them by their own references rather than presuming they are included.
If the original number is unavailable, take clear photos of both sides of the gasket and the mating joint. Include a scale in the same plane and show the full perimeter, holes, notches, and orientation. A measured tracing can aid comparison, but a used gasket may have stretched or compressed. Measurements should support, not replace, the official part reference and assembly drawing.
Safe teardown and surface preparation
Park and isolate the machine on stable ground. Lower the attachment, secure components against movement, and follow the service manual for stored energy, drainage, and lifting. Planetary or final-drive parts can be heavy; use rated lifting equipment and trained personnel. Keep the work area clean and protect open housings from dirt, water, and loose hardware. Record the direction and location of covers, carriers, shims, and retainers before removal.
Once the joint is open, remove old gasket material with a method suitable for the housing. Avoid hard scraping or abrasive discs that can score a sealing face. A scratch crossing the seal path can allow leakage even when the replacement is correct. Inspect the joint for corrosion, dents, raised burrs, cracks, and distortion. Check for abnormal wear or contamination inside the assembly and document findings before cleaning them away.
Use sealant only if the manufacturer specifies it for that interface. Some gaskets are installed dry; others require a particular sealing compound in defined locations. Excess sealant can squeeze into gear or oil passages and cause damage. The listing provides no sealing procedure, so follow the machine manual. Replace a gasket that the service procedure identifies as single-use after separation.
Installation and post-repair checks
Before installation, compare the replacement perimeter, openings, holes, orientation, and any locating tabs with the original and the parts drawing. Ensure the housing faces are clean and dry or prepared as instructed. Align the gasket without stretching it. Bring mating parts together without sliding the gasket out of position. Tighten fasteners in the specified sequence and to the correct values from the manual; no torque data is stated here.
After assembly, refill the exact lubricant to the prescribed grade and level. Follow the required operating or leak inspection steps. Check the joint under the approved conditions and inspect for seepage. If leakage persists, investigate surface condition, alignment, fastener sequence, and part identity rather than tightening beyond specification or applying extra sealant. Record the part number, lubricant, machine hours, and inspection result for future service.
How to request a reliable quotation
Provide part number B00256+75201605, the machine plate, full serial number, gear assembly location, and the diagram callout. Include images of the removed gasket beside a scale and of the open mating surfaces. State whether the repair is a scheduled inspection or a leak-related teardown, and ask the supplier to confirm package quantity and any associated seals. This lets the parts desk check the exact assembly instead of guessing from a broad description.
Keep this part separate from other axle and joint items. See the half axle gear gasket B00256+75201604 record and the lower joint shaft listing; their descriptions do not establish interchangeability with this planet gear gasket.
Frequently asked questions
Does the record show the gasket’s dimensions or material?
No. Confirm the outline, thickness, material, and mating assembly through the parts drawing or verified sample.
Is this gasket for a particular final-drive model?
The listing does not provide a model application table. Verify the exact assembly and serial range before ordering.
Should sealant be used?
Only use the sealing method specified for the joint. Applying unapproved compound may affect fit or contaminate passages.
What should be checked after fitting?
Confirm correct alignment, fastener sequence, lubricant level, and the prescribed leak inspection. Investigate any continuing seepage at the joint.
Catalog summary
| Catalog item | Planet gear gasket |
|---|---|
| Part number | B00256+75201605 |
| Category | Lovol Excavator |
| Joint application | Not stated; verify by machine serial and assembly drawing |
Accurate gasket selection protects a cleaned and correctly assembled joint. Confirm the exact housing, part number, and sealing procedure before the unit is closed and returned to service.