Description

This listing uses the name “release valve” and part number 9B650-35A040000A0, with the catalog category Lovol Excavator. The record does not identify the valve’s circuit, pressure setting, port arrangement, thread, dimensions, material, or compatible serial range. “Release valve” is not enough to determine whether it belongs to a brake, hydraulic, pneumatic, or another assembly. Confirm its exact location and function from the machine’s parts diagram before ordering or installing it.

Start with the circuit, not a guessed function

Valves can share a similar appearance while controlling different fluids and operating conditions. A release valve may have a specific role within a designed circuit, but this product page does not define it. Do not assume a pressure rating or infer that the valve is a safety relief component. Follow the system diagram and the manufacturer’s terminology. If a technician has identified a suspected valve, document the assembly and the diagnostic steps that led to the part reference.

Symptoms such as slow response, a warning indicator, pressure fluctuation, leakage, or a component that does not release may arise from multiple sources. The valve may be one possibility, but lines, seals, controls, filters, actuators, fluid condition, or upstream supply may also matter. A qualified technician should test the identified circuit using the correct procedure and instruments. No pressure specification or test point is provided by this listing.

Verify part number 9B650-35A040000A0

Copy the full number, including the prefix and suffix. Compare it with the callout in the serial-specific parts diagram and check for revisions or supersessions. Record the valve’s exact installed position, orientation, ports, connectors, and any stamped labels. Photograph all sides before removal. If the valve is already removed, preserve its tags and fittings and note which port connected to each line. Do not rely on memory when multiple similar components are present.

Ask a supplier to confirm the part number against the machine and the specific circuit. The listing does not state whether the valve is supplied with seals, solenoids, fittings, or a mounting block. Clarify package contents and any required companion parts separately. If the original number is unreadable, provide the machine plate, system diagram reference, photographs of the mounting location, and measurements taken with appropriate tools.

Safe inspection and removal

Before work begins, secure the machine, lower equipment, isolate energy sources, and relieve stored pressure as directed by the service manual. Some circuits can retain pressure after shutdown. Never loosen a fitting to test whether pressure remains. Use the proper procedure and personal protective equipment. Keep the work area clean, collect fluid safely, and cap open lines using clean approved caps to prevent contamination.

Clean the outside of the valve and surrounding area before removal so dirt cannot enter the circuit. Mark orientation and label every connection. Use the correct wrench on the intended flats to avoid twisting a line or damaging a port. Inspect the valve body, connector, mounting face, and seals for visible damage or corrosion. Do not disassemble an internal valve or alter an adjustment unless the manufacturer’s instructions permit it.

Fluid contamination can affect precision components. If debris, water, or abnormal residue is present, document the finding and follow the circuit’s flushing and contamination procedure. Replacing one valve without addressing contaminated fluid or an upstream failure may not resolve the issue. Use only the fluid type specified for the identified system and keep incompatible fluids separate.

Installation and functional verification

Before fitting a replacement, compare the number, port layout, mounting footprint, connector, and orientation with the approved drawing. Confirm whether seals must be renewed and how the threads or sealing faces are designed. Do not force a fitting or apply thread sealant indiscriminately; some ports seal at a face or with a specific ring. Use the prescribed tightening method and values from the machine service data. This page does not contain torque or pressure values.

Reconnect each line to the documented port and secure its routing so it does not rub or carry side load. Restore guards and supports. Refill or top up fluid only as instructed, then prime or purge the system according to the manufacturer’s procedure. Perform static checks first. When an operational test is required, keep people clear of moving equipment and test in a controlled area. Check for leaks and correct system response under the specified conditions. Stop if the warning or abnormal behavior remains.

Record the diagnostic result and the installed part number. If the valve was replaced because a release function was absent or delayed, document the test that confirmed restoration. A part change alone should not be taken as proof that the whole safety-related system is functioning; complete all required inspections before returning the machine to work.

Information for a parts quotation

Send part number 9B650-35A040000A0, the machine identification plate and serial, the relevant diagram page and callout, circuit name, and clear photos of the valve and ports. Include any label or number on the old part. State the observed issue and what tests were completed, without guessing at a pressure setting. Ask the supplier to confirm fitment, connector details, seals, and package contents in writing.

For context, this release valve should be treated as distinct from the foot brake valve 9F850-36A020000A0 and the oil return filter 9F850-58A050000A0. Similar category or part naming does not establish a shared circuit or interchangeability.

Frequently asked questions

What system does this release valve belong to?

The catalog record does not state the circuit. Confirm the assembly location and diagram callout for the machine serial.

Is a pressure setting available?

No pressure value, flow rate, or test procedure is published here. Use the correct machine service documentation.

Can I install a valve with similar ports?

No. Verify the part number, circuit, port design, connector, and serial application. Similar appearance is not proof of fitment.

What should be checked after installation?

Follow the circuit’s fill, purge, leakage, and functional test procedure. Do not return the machine to service until the required system checks pass.

Catalog summary

Catalog itemRelease valve
Part number9B650-35A040000A0
CategoryLovol Excavator
Circuit and settingNot stated; verify by machine serial and system diagram

Accurate identification of the valve’s circuit and part number is essential because its name alone does not define a safe or compatible replacement. Confirm the application and testing requirements before ordering and again before commissioning.

FREE Inquiry Now

If you have any questions, feedback or comments, please fill out the form below and we will reply you back as soon as possible.

+86-130-4508-1859

Get A Quote