Description

SJM03-1,70 is the scraper seal reference in this wheel loader catalog. Copy the comma and adjacent numbers exactly as shown. A scraper or wiper seal is generally used to clear debris from a moving surface where the approved design calls for it. Match the catalog drawing position, cross-section and associated groove before placing an order. The code on this page does not confirm dimensions, material or compatibility with a specific cylinder or machine.

Part identification before ordering
Listed referenceSJM03-1,70
Catalog descriptionScraper seal
Compare the sampleCross-section shape, lip orientation and mating surfaces
Confirm the installationExact assembly and parts drawing callout, suitable groove data and material requirement
ScopeIdentify one seal position or state the separate kit requirements

Where the number was found matters

A seal might come out with little or no readable marking. The useful identification may be printed on a repair-kit label or in a diagram rather than on the seal itself. State where you found SJM03-1,70. Send a clear photo or a cropped drawing showing the exact position. Add the equipment and assembly references so the seller can distinguish a positive match from a previous repair note. The punctuation and suffix can be preserved in the typed message even if the supplier's search engine normalizes them.

Avoid reading “70” as a confirmed dimension solely because it appears at the end of the reference. Give the documented groove and mating measurements their own labeled fields. If the part is being assessed from a photograph and a worn sample, state which values came from each source. Have the workshop confirm a discrepancy before approving a substitution. A verified dimension from the correct assembly drawing is stronger evidence than a guess based on numbers printed side by side.

Photograph the cross-section and the installed orientation

Take one image of the overall seal and another of the profile when it can be observed without destroying evidence the technician still needs. Mark the side that faced the exterior and the side that faced the protected area, if known. A worn lip can fold or flatten, changing what it looks like in hand. If that has happened, send the parts drawing and a clear image of the groove or retaining shoulder. Label photographs taken after removal as supporting evidence rather than treating them as a perfect representation of the original profile.

A nominal size may be useful in narrowing the available forms, but the lip style and groove arrangement still identify how the seal is expected to seat. Where material, working conditions or media compatibility matter, request the data for the exact offered version. A buyer should not assign material from the color of a degraded seal. The approved documentation or supplier specification is the place to resolve that question.

Confirm which position the purchase line covers

A repair ticket may call for “a set of seals” after several parts are removed from the same assembly. A scraper seal has its own position. A seal that performs another internal function should keep its own expected profile and reference. Quote the part positions as separate lines where they can be identified. If the seller offers a kit, request an itemized list that names the scraper and identifies which other pieces come with it.

The DG930A-09003A sleeve listing is a separate component reference for a related loader catalog search, with its own location and dimensions. The Shantui loader parts category provides links for additional purchases. The catalog does not establish that either reference forms a documented pair with this seal. Confirm parts by their own drawing callouts.

Work order example from an identification request

A fitter sends the stockroom a small seal in a bag marked “scraper.” The seal lip is worn and the stockroom measures the piece but cannot locate a legible maker mark. The repair sheet for the machine contains the code SJM03-1,70. The buyer needs to connect that code to the particular groove before ordering. Ask the fitter to mark the original position and attach the drawing. Record the approximate measurements from the old seal, and label them as worn sample measurements. Now the supplier can compare a definite position and reference even when the physical sample cannot show its original dimensions accurately.

If several versions are available, request a sketch of the offered profile and a statement of the material or specification where it is needed for the application. Make the workshop's approval part of the purchase record. A successful comparison gives the receiver something more concrete than a package marked “wiper”: the exact code, accepted profile and expected piece count.

Count and identify the delivered seals

Inspect the package labels and keep different profiles in separate bins. The lip can be difficult to distinguish while several seals are stacked in one bag. Where a part is individually packaged, leave its label linked to the drawing position until the workshop checks it. If the marking has been printed using a different punctuation style, ask the seller to confirm the correspondence in writing and retain it with the order. This avoids creating two uncertain stock records for the same approved replacement.

For a part that is held in stock, record the complete designation and installed location once the workshop verifies it. If the same machine has more than one scraper seal on a parts drawing, a separate named position on the stock card helps the next buyer find it.

Before sending a sample to identify the profile, label its bag and record which surface was worn. Send the drawing position electronically as well, since a removed seal can be photographed from either face and the package may arrive without the workshop annotations. If the seller compares several candidates, ask for the drawing or profile sketch that supports the chosen offer. Keep that sketch with the receipt rather than separating it from the packing reference. Reordering a known scraper is quicker when the store can retrieve the exact shape and named position.

Frequently asked questions

Does 70 in SJM03-1,70 confirm a 70 mm size?

Use the drawing and actual groove data to confirm dimensions. Keep the original catalog number intact and ask the supplier to state the nominal sizes of the offered part separately.

Can this scraper seal replace another seal of the same outer diameter?

Compare the full lip profile, groove dimensions, installed orientation and applicable material or service requirements. A single matching diameter cannot establish that the new seal suits the correct position.

What should I send if I cannot read the original part?

Send the drawing callout, an image of the removed part and groove, and the actual assembly identification. If the part was removed without recording its position, describe that uncertainty and ask the workshop to confirm the callout.

FREE Inquiry Now

If you have any questions, feedback or comments, please fill out the form below and we will reply you back as soon as possible.

+86-130-4508-1859

Get A Quote