ZL30GII 04200 is the catalog reference shown for this front driving shaft. On a purchase request, keep the two parts of the reference together and identify the assembly and exact front shaft position in the parts drawing. Compare the parts at both ends, the locating faces and the specified length. The original entry does not establish a complete model or serial range for every installation.
Part identification before ordering| Catalog reference | ZL30GII 04200 |
|---|
| Catalog description | Front driving shaft |
|---|
| Assembly evidence | Installed drivetrain identification and front shaft callout |
|---|
| Interfaces to check | Flange or spline details, bolt pattern, pilot and end-to-end orientation |
|---|
| Supply scope | Confirm the delivered shaft and any explicitly included joints or mounting pieces |
|---|
Put the direction and installed position on your photographs
The word “front” is helpful when the fitter and supplier look at the same diagram. Label the end toward the front axle, or use the orientation in the maker's service literature if the position differs from that description. Put a photo of the original installation alongside the fully removed shaft when available. This helps a seller distinguish this front driving shaft from another driveline section that may look similar once it is on a bench.
A photograph on its own can invert the apparent position. Show the complete assembly and mark which end was attached to which adjoining component. Use a consistent label for each end on the sketch and the detail photos. If part of the original vehicle identification is unclear, provide the installed assembly tag and any previous exchange history. The seller can use the combination to check the correct parts drawing rather than assigning a shaft based on the front or rear description alone.
Record flange and spline conditions without guessing the build
For a flanged end, capture the face straight on and document the pilot, bolt pattern and any locating step indicated by the drawing. For a splined end, show the profile and any features that distinguish the fitting. If the parts drawing describes an interface different from the component removed from the machine, state the difference explicitly. A photograph from an angle can make two patterns appear similar, particularly when the circles and clearances are not marked.
Where an older job left an adapter in place, verify whether it is a separate part or normally part of the supplied shaft assembly. Tell the supplier which items are wanted in the new shipment. If the offer includes loose hardware, ask it to appear on the inclusion list. A receiving team handling separate shaft and joint deliveries needs to know which item numbers correspond to which work order.
A length value needs accompanied reference faces
Describe how and where a length was measured. A drawing may give the distance between flange faces, a total including raised projections, or a length in a defined installed position. If the assembly has a sliding section, use the measurement condition stated on the documented drawing and share it with the supplier. A single dimension written as “shaft length” may hide the only substantial difference between candidate parts.
A used, damaged component can provide helpful comparison evidence. Where the work order relies on it, mark any visible condition affecting measurement and attach the nominal value from the approved drawing if available. The supplier should be able to return a dimensioned illustration identifying both ends and the length convention for the offered unit. Ask the fitting shop to compare that proposed reference before a substitute is accepted.
Quote the shaft and supporting hardware as separate decisions
Start with the front shaft and confirm the commercial supply boundary. The repair may include a complete shaft as listed by the supplier, individual associated components or only a shaft body. Have the supplier confirm what is covered, and include any other parts using distinct lines and catalog positions. The main driving shaft catalog entry shows a separate listing whose position also needs to be established. It is not evidence of interchange with 04200.
The intermediate bearing case assembly listing represents a separate support part. When a work order refers to a support and shaft together, identify both on the actual assembly drawing and ask for their respective supply limits. Use the diagram to establish whether the requested pieces belong to the same work order rather than treating related catalog links as a documented pairing.
How the same model reference can cause a false match
Consider a buyer requesting a shaft for two fleet machines on the same order. One job is a front shaft repair, and the other concerns a different driveline position. Both were described by the workshop under the same model family. A useful buying sheet identifies each unit's serial and installed drivetrain and keeps the part position on each line. Attach the 04200 reference only where the machine drawing confirms the relevant position. Store the photos by work order so the supplier can see which interfaces belong to which request.
If the exact fit remains uncertain, ask for the dimensional drawings of the possible alternatives and list the missing evidence on the sheet. The purchase should remain conditional until the shop resolves the choice. Making the question explicit helps prevent shipment of a shaft that has the same generic description but an incompatible end or mounting length. Refer to the machine documentation for installation and inspection once the correct part is available.
For a shaft ordered from a distance, ask the supplier for views of the two mating faces alongside the label and the referenced dimensional drawing. Keep that record with the shipment instead of relying on the carton alone. If the site needs the shaft by a certain day, a receiving technician can compare the interfaces with the approved drawings before moving the package to the machine. Escalate any difference while the buyer can still identify the supplier's exact offered variant. Once accepted, record the installed unit and position in maintenance history so a repeat purchase can start with the verified reference.
Frequently asked questions
Is 04200 enough to identify the front shaft?
Use the full listed reference ZL30GII 04200 and the installed drivetrain drawing. A short code may be reused or quoted without its family context. Ask the supplier to confirm the assembly and flange or spline details.
What does the assembly include?
The original catalog identifies a front driving shaft. Request an itemized quotation for the supplied unit and any joints, fasteners or other pieces the seller offers with it. Keep the separate scope on the purchase order.
Can the dimensions be taken from another loader in the same fleet?
Use a verified drawing or part from the actual installed configuration. Another loader in the same fleet can help the workshop locate likely documents, and the serial and assembly data establish the reference for purchase.