Description

This axle gear washer is listed as a wheel loader spare without an exact part number. Identify it on the illustrated axle assembly and show which side of the gear or carrier it sits against. A washer may look like a simple ring when seen in isolation. Position, thickness and any tabs, flats or radiused surfaces make a replacement comparison more specific. Use an approved part diagram or drawing to establish the intended specification.

Part identification before ordering
Catalog itemWasher for axle gear
Confirm the positionAxle or differential assembly, gear identity and washer callout
CompareInside diameter, outside diameter, thickness and locating features
Workshop evidenceInstalled orientation and the face that touches the gear
Order scopeOne washer or a documented set of selected pieces and quantities

Recover the intended position from the parts layout

An axle can contain several ring-shaped components. Some lie near a gear face while others belong to a bearing adjustment, retention or spacing arrangement. Identify the washer from the assembly drawing rather than relying on where a loose ring was found during teardown. Highlight the relevant branch and show the neighboring components so the supplier can identify which washer you mean. Give the repair technician a chance to confirm the intended position if the part was removed before a record was made.

Record which face was against the gear, where known. If the washer has an uneven shape, take a picture from above and one from the side. Make a close-up of locating tabs, flats or holes where present. A line on a worn washer can be a wear mark rather than a designed channel. Attach a photo and the original documentation when that distinction matters for replacement. The maker's illustration or an approved sample gives the quote a sounder basis.

Separate thickness data from evidence of wear

An old washer may measure thinner where it was worn. Mark why a thickness measurement was taken and identify the surface or points measured. If readings differ across the part, report that variation and let the workshop check what the nominal thickness should be. A measured value from a worn component can help an identification discussion. The replacement should match the requirements for the approved axle assembly and position.

Document inside and outside sizes separately. If the buyer gives three numbers from a voice message, ask for labels before passing them on. The sequence may mean different things to two suppliers. A simple dimensioned sketch or a readable piece of the original parts drawing can settle the confusion. Ask the supplier to show where it measured any compared part. This makes it easier to distinguish a genuinely matching washer from a flat ring that only shares one dimension.

Keep the washer and gear identities connected

Where the gear has its own part number, include it as supporting context and identify the washer as a separate requested line. The 50M.01-22 axle shaft gear page is an example of a gear identified by its own number. The wheel loader bevel gear and washer page covers a separate catalog entry whose commercial inclusion list also needs confirmation. Neither page establishes that this standalone washer is included or is a confirmed match to a particular gear.

Ask the supplier to quote the right unit of measure. If the workshop needs two washers, say whether those two positions use the same reference or two different ones. Some orders require an individual washer while others request a set. A seller can quote a set if its contents are documented, and the buyer can compare it against the position count on the work order. Describing the required shape and position matters as much as counting the number of rings in a package.

A practical example when the wrong type was supplied earlier

Suppose a previous repair left a flat ring in stock labeled only “for axle gear.” The current drawing shows that the requested washer sits at a different position or has a feature that the stored piece lacks. Keep the old package and photograph it. Ask the workshop to attach the current drawing and identify the difference before ordering. Do not dispose of the earlier record, because it may explain why inventory shows stock even though the correct washer is missing.

Make the quote specific enough to resolve the mismatch. Identify the axle and gear location, the nominal thickness from an approved source and the face geometry needed. Ask for a line drawing or photo of the offered washer with the identifying features visible. At receiving, compare the delivered mark and shape with that quote. An earlier mismatch is easier to avoid when the buyer captures precisely what distinguishes the new part from the leftover piece.

Record the result for repeat orders

Once the workshop confirms the match, record the assigned reference and the exact assembly position on the stock card. Link it to the axle or gear drawing and name the reference faces used to compare thickness. Keep separate SKU records where two positions use similar washers with different requirements. A buyer can then retrieve the documented selection rather than making a new guess after the machine has returned to service.

If a quote offers optional washers for other positions, keep those lines identified apart from the confirmed one. This protects the work order when a warehouse receives all items in the same carton. Save the supplier's traceable item label, selected application and approval in the receiving record. The resulting file tells the next person what was bought, where it was used and which drawing was consulted.

When the axle is rebuilt by a contractor, give the rebuilder the approved washer position and drawing before the parts arrive. Ask for a marked receipt that makes clear whether the washer was found in the itemized gear package or supplied from a separate line. If the rebuilder selects a different part, record its identity and the reason on the job sheet. The stockroom then has an accurate record to use for the next axle repair, including whether it needs to retain a dedicated washer line.

Frequently asked questions

Does this washer have a confirmed part number?

The catalog entry names the part without a verified number. Provide the installed axle identification, gear information and the washer callout for a targeted quotation.

Can I substitute an ordinary flat washer of the same outside size?

Check the required dimensions, seating faces, locating details and documented application. An equal outside diameter does not establish the appropriate washer for that gear position.

What photo helps if the old washer is damaged?

Send clear pictures of both faces, the neighboring gear or housing and the installed position if it's known. Identify wear or damage separately and include the drawing so the original shape can be compared.

FREE Inquiry Now

If you have any questions, feedback or comments, please fill out the form below and we will reply you back as soon as possible.

+86-130-4508-1859

Get A Quote