This wheel loader catalog entry covers a bevel gear and washer. A separate order code is not shown in the original listing. Use the axle assembly identifier and the drawing positions for both pieces to establish which pair is required. A picture of a bevel gear that resembles the removed part can help identify its family, while the bearing face, exact gear geometry and washer shape determine whether the proposed pair belongs to the same location.
Part identification before ordering| Catalog item | Bevel gear and washer |
|---|
| Identifiers to request | Gear callout, washer callout and installed axle or differential reference |
|---|
| Gear comparison | Tooth and bore details, hub form, cone orientation and thrust face |
|---|
| Washer comparison | Inside and outside dimensions, thickness, locating features and installed orientation |
|---|
| Quotation | Ask whether the offer covers one gear, one washer, or an explicitly itemized set |
|---|
Begin with two lines even when the catalog groups the pieces
The words “and washer” describe an association that matters to the repair. Begin the buying request with one line for the gear and another for the washer. Add each callout to its line, then allow the supplier to quote a set if those exact positions are offered together. This preserves scope for a buyer who discovers that the old washer is unsuitable for reuse. It also prevents duplication when a gearbox kit or differential assembly on the same order already contains the required piece.
If an internal quote system allows only one line for the pair, put the two quantities and references in the description. Ask the recipient to repeat the inclusion list on its acknowledgement. That acknowledgement becomes the floor check at receiving. A carton marked “bevel gear set” can refer to multiple gears in some orders, while the buyer may expect just one gear and its backing washer.
How to photograph the gear when the original number is missing
Photograph the gear square to its face and from the side, with a known orientation. A side view shows the hub projection and the axial form that a face photo hides. Record which face ran against the washer and show that face separately. If the gear is part of a differential, identify the rest of the assembly in the drawing. The supplier can then compare the original gear with the offered position instead of trying to assign an unfamiliar part by a damaged or angled picture.
Record the tooth count and any center features the workshop can confirm. A plain bore, a splined bore and a shape with a locating feature should each be described explicitly. Photographs of similar conical gears can look close at a glance while those distinctions are hidden by shadows. Keep material and heat treatment questions with the approved parts documentation unless the actual product specification provides them. Appearance alone offers little basis for a claim about either.
Keep the washer tied to its installed face
The washer transmits contact across the designated face and may locate against a shape in the axle or gear. If a washer is asymmetric, note which face met the gear and which faced the housing. An old washer can develop a visible wear path that helps recall that orientation. When the part is removed, photograph it on both sides and include a close-up of tabs, holes or locating details. This is useful even when the washer is later confirmed from a separate line on the parts drawing.
Thickness readings should be labeled so the supplier can see whether the value came from a worn washer or approved documentation. A worn part is often an unreliable basis for establishing the nominal size. If there is a conflict, share both readings and ask the service team to confirm the intended part before release. A separate axle gear washer page can help describe the type of information to request. It carries its own fitment check.
When the request mentions a bevel gear set
Ask the workshop what is physically needed. “Bevel gear set” could mean one gear and its thrust washer, two meshing gears, or a set supplied under a differential assembly number. The name is a useful description and a poor substitute for an inclusion list. A request that begins with “one bevel gear, one washer, drawing positions attached” can be answered without either side interpreting the word “set” on its own.
For axle jobs that include an axle shaft gear, the 50M.01-22 axle shaft gear listing illustrates how a stamped or printed gear code can be included as its own purchase line. This listing for the bevel gear and washer has no confirmed 50M.01-22 cross-reference. Let the installed axle drawing determine whether the two records concern different positions or different assemblies.
Receiving a pair across two shipments
A buyer sometimes receives the gear ahead of its matching washer. Keep both ordered positions open until each is received and checked. Store the first item with the purchase line and the related machine or axle identifier. When a visually similar washer from another order appears, avoid moving it into the open job merely to complete a kit. The approved callout and shape are the evidence for assembling the order together.
The fitter should also be able to tell which evidence a buyer relied on. Include pictures, supplier drawings and itemized quantities with the work order, especially where the product listing lacks a fixed part number. A clear receiving record answers what was supplied and which machine it was ordered for. Assembly and adjustment values come from the applicable service information.
These details are also useful when another shift takes over the teardown. Keep a view of the installed position alongside the cleaned component photos so the buyer can see how the parts were arranged. If the gear and washer were already separated when the work began, mark the original arrangement as unknown. An installed-position photograph from the same work order carries more weight than a similar image from another loader, even if both machines carry the same brand badge.
Frequently asked questions
Does this entry identify a particular wheel loader model?
The catalog entry does not state a confirmed model list. Supply the loader identification, installed axle number and drawing positions for the gear and washer. Ask whether the offer matches each callout for the given assembly.
Can I purchase only the washer?
Specify the washer drawing reference and the original drawing position. Provide thickness, shape, locating features and photos of both faces as supporting evidence. Ask for a one-piece quote or an itemized answer if the supplier normally offers the parts together.
What if the gear and washer in the illustration are drawn as one unit?
Look for separate callouts and inspect the catalog description for the exact unit of supply. If the diagram does not distinguish the pieces, ask the supplier to name the offered contents in writing before approving the purchase line.