The 50M.01-22 axle shaft gear is listed as a wheel loader drivetrain spare. Use 50M.01-22 as the ordering reference and confirm the actual differential or axle assembly where the gear will be fitted. The listing identifies a gear. A buyer who needs its associated washer, mating gear or complete differential should describe those lines separately so each scope can be confirmed at quotation.
Part identification before ordering| Product reference | 50M.01-22 |
|---|
| Catalog name | Axle shaft gear |
|---|
| Assembly evidence | Installed axle identification and differential or axle drawing callout |
|---|
| Key checks | Tooth count and direction, internal spline details, hub dimensions and thrust face |
|---|
| Quote scope | Specify the gear and list any mating parts as separate lines |
|---|
Put the gear on the right branch of the diagram
An axle assembly drawing can contain several toothed components and multiple positions that a service note might call “axle gear.” Show the supplier the drawing branch and highlight the specific part position. Include the page region that shows what runs through or against the gear. A highlighted bubble by itself can be harder to interpret when the catalog uses the same callout number on different pages. The printed reference 50M.01-22, the assembly identifier and an attached photograph together make a clearer inquiry than the full loader model by itself.
When a matching drawing cannot be found, label the removed gear by its physical location before it leaves the machine bay. Note the axle position and which side or housing the piece came from if the mechanic can confirm it. Keep those notes with the photo rather than as live chat messages that disappear from the purchase record. An old gear that has passed through several hands can be visually correct and still belong to a different repair job.
Splines and thrust faces do different jobs
A front photograph shows the tooth ring and center, but it often hides the spline depth and back face. For an identification request, take a picture looking straight through the center, one of the tooth profile, and one showing the hub and rear face. Record tooth and spline counts separately. If a worn tooth makes a count doubtful, flag the uncertain value. A supplier may be able to resolve it through the OEM drawing, whereas a guessed count can send the comparison in the wrong direction.
The rear face deserves its own picture if the gear is used with a thrust washer. The bearing surface, reliefs or locating shape can help distinguish a fitted pair from a superficially similar spare. Confirm the interface against the drawing for 50M.01-22 rather than assuming that a washer found in the bottom of a housing belongs to the gear. For a separate line item, see our axle gear washer listing. Confirm that washer by drawing position too before adding it to a 50M.01-22 order.
Use the mating parts to describe the job, then set the scope
A buyer may want a single gear because the workshop has assessed the mating components and approved reuse. Another workshop may request several items after opening an axle and finding wear across multiple faces. In either case, a sheet with one row per requested item is clearer than the instruction “send everything around this gear.” Keep the gear number 50M.01-22 visible on the first line, then add the washer, cage, or other parts only when each callout is identified.
If the quotation mentions an assembly rather than an individual gear, ask for its inclusion list. A quoted differential can carry its own assembly number and may have a separate arrangement of internal parts. The scope should say which part numbers, quantities and positions the quotation covers. The Shantui wheel loader spare parts category can help the buyer reach neighboring listings. Each listing must be matched to its own diagram position.
A field example from a mixed fleet
Picture a service shop working on two loaders of similar age. A gear for one job is carried over to the stockroom for measurement while the second axle arrives on a pallet. Both jobs are labeled “loader rear axle parts.” The buyer can prevent the records from merging by writing the work order on each photographed part, assigning the assembly identifier to both lines and naming the intended position on the drawing. Where the first gear is positively identified as 50M.01-22, that reference belongs only to the first confirmed position until additional evidence establishes a match.
A reference from a previous order can reduce work when the repaired assembly is the same. Check whether the same axle was present at the time. The serial or assembly number on an exchange axle may differ from the old repair record. Keep the previous invoice as evidence of what was supplied once, and mark any current difference for the technician to resolve before ordering.
Check what arrives while the packaging is still identified
Match the label and count the gear teeth and internal splines against the approved quote and the drawing. Compare both faces with the recorded pictures before moving the gear to an open parts tray. Note the manufacturer reference if it differs from the catalog reference, and record the agreed cross-reference rather than relabeling the gear with only the model of the machine. Photographs made at receiving also make it possible to identify a mix-up without drawing conclusions about how the old gear failed.
Leave the work order and its part identification connected so the fitting team can retrieve the approved line. Questions about adjustments or the condition of adjoining components belong with the service technician and the axle documentation. A supplier's parts comparison establishes that a proposed gear corresponds to the approved reference. The repair procedure remains specific to the assembly.
When a supplier proposes an alternate code, put both numbers on the acknowledgement and attach the drawing or approved cross-reference that connects them. The mark on the delivered gear can then be checked against the version the workshop actually approved.
Frequently asked questions
Is the 50M.01-22 washer included automatically?
Request written confirmation of the offer scope. Quote a washer separately when it has its own drawing reference, and record each piece the workshop expects to receive. The presence of a washer in an exploded diagram shows where it belongs, not what is included in a commercial package.
Which photos make a spline comparison worthwhile?
Send a straight-on photo through the bore and a side view that shows the spline length and hub. Record the count alongside the images, and include a full view so the supplier can orient the close-up correctly.
Does an axle model in common establish gear fitment?
It establishes a catalog starting point. A drawing matched to the installed assembly and the exact gear position carries more weight than a common axle family name. Check the reference and keyed interfaces on the actual assembly before treating it as confirmed.