The 31314 single-row tapered roller bearing is listed here under the catalog reference GBT297-94, 31314. Use the complete markings on the cone and cup, the bearing position on the assembly drawing, and the specified envelope dimensions to confirm a replacement. The catalog entry gives a starting reference for a wheel loader repair. The axle serial number or a verified parts diagram is needed to establish machine fitment.
What to identify before ordering bearing 31314| Catalog reference | GBT297-94, 31314 |
|---|
| Bearing family | Single-row tapered roller bearing |
|---|
| Markings to capture | Full cone and cup designations, suffixes and manufacturer's mark |
|---|
| Envelope to verify | Bore, cup outside diameter and assembled width, measured against the product drawing |
|---|
| Fitment evidence | Axle or drivetrain assembly identification and the bearing callout for its actual position |
|---|
Read the cone and cup separately
The cone is the inner ring with the roller and cage assembly. The cup is the outer ring that sits in its housing. A technician may have the cone on the bench while the cup is still in the carrier. A photograph of one ring can therefore leave the supplier without half of the ordering information. Photograph both markings where they can be read safely, and transcribe letters and numbers as well. If the second marking is damaged, share the assembly drawing and any packaging label from a documented previous replacement.
Ask whether the quotation covers one complete cone-and-cup set or one component only. The distinction matters when two buyers use the same short description, such as “one 31314.” One may expect one complete bearing and the other a cup. Put the intended unit on the purchase order, particularly if the workshop is preparing two bearings for opposing positions. When the removed components have different markings, record those as separate lines until their positions have been checked.
Confirm the bearing position before cross-referencing it
Wheel loader maintenance requests often start with the equipment model on the front of the machine. The driveline assembly fitted to that machine may have a narrower serial range or its own supplier reference. An axle tag, housing identification, and the callout on the parts illustration make it easier to establish where the bearing belongs. A workshop should be able to point to the actual location and show which face of the installed bearing was visible before it was removed. A bearing from a similar looking housing may fit a different shaft diameter or mounting depth.
Position is particularly helpful when the workshop request uses broad language such as “axle bearing,” “carrier bearing,” or “wheel bearing.” Those terms cannot establish whether the reference came from a wheel end, a carrier or another drivetrain assembly. Attach a marked crop of the relevant drawing and include the full assembly number in the request. If the repair also calls for a complete axle or gear unit, quote that separately. Our XCMG QY25K middle drive axle listing shows how a complete axle is identified by its own assembly reference. The crane axle is a separate product with its own fitment.
Use measurements to resolve a doubtful match
Start by recording the shaft bore requirement, the outside diameter of the cup and the overall width when the bearing is assembled. Keep the measurement units beside each value and mark which dimension came from the original part and which came from the assembly drawing. For example, the individual ring width and assembled bearing width are different entries on many bearing drawings. A photo showing exactly where a dimension was taken can save the supplier from treating these measurements as interchangeable.
If the original ring was damaged or spun on its seat, have the maintenance team compare its readings with the approved drawing. A distorted component can produce a misleading measurement. The supplier should check the designation, manufacturer drawing and ring combination together before offering a cross-reference. The designation 31314 is useful for narrowing the search. Record any suffix as it appears, including punctuation, and ask the supplier to state the full offered designation on the quotation so the workshop can review the proposed version.
A practical fitment check after the axle is opened
Suppose a fleet workshop opens a loader axle during a repair and finds that the original bearing marking is partly readable. The mechanic recognizes 31314 on one ring. The buyer can send that photo with the loader identification, axle serial, diagram position, quantity and the ring measurements. The workshop can also record which other parts were found on the same shaft, such as a spacer or shim. This establishes what the supplier is quoting and gives the technician a way to verify that the bearing comes from the correct position in the assembly.
If the job began with drag or heat at the wheel, give the technician room to check the symptoms before raising a purchase request. Braking parts and drivetrain bearings are quoted against different assemblies. For a separate brake work order, see the Lonking loader parking brake assembly for an example of identifying the brake by its own assembly reference. A bearing listing alone cannot diagnose where drag originates or establish that any brake component is involved.
Check the delivered set before the job is scheduled
At receiving, compare the delivered label with the approved quotation before assigning the bearing to a work order. Keep the cone and cup in their packaging until the technician can confirm both markings and count the pieces. If the label differs from the approved designation, record the difference with a photograph and ask the supplier to identify the reason. Add the confirmed bearing position to the store record so a later buyer can distinguish this order from another axle repair.
Frequently asked questions
Will 31314 fit every loader that uses a similar axle housing?
Fitment needs to be confirmed for the actual axle and bearing location. Provide the axle identification and the diagram callout along with the bearing numbers. A similar casting or shared equipment model name is only preliminary evidence.
Can I buy a cup separately when the cone looks undamaged?
Ask the workshop to specify the approved cone and cup combination, and ask the supplier whether the quotation includes both components. The equipment and bearing documentation govern whether an individual ring is an appropriate replacement for that assembly.
What do I send when the cone marking is too worn to read?
Send the readable cup marking, a clear photo of the other ring, the assembly drawing and the three envelope measurements. Include the exact installed position and any traceable previous packaging label. These records help a supplier identify the remaining checks before quoting.
Where do I find the adjustment value for installation?
Use the maintenance instructions for the specific axle or drivetrain assembly. Quote and receiving checks establish the part identity and package contents. The assembly manual governs preload, clearance, adjustment sequence, and any inspection required before the loader is returned to service.
For a quotation, send 31314 with photos of both markings, the axle or assembly identification, the drawing position and the number of complete bearing sets required.