Shantui Bulldozer O-Ring 07000-63025
Shantui Bulldozer O-Ring 07000-63025 is the catalog reference for this page. The details below are written for purchasing and service teams who need to match an existing component, not for guessing from a broad machine family. Confirm O-ring 07000-63025 by its full code and installed groove. Do not substitute the nearby 07000-63022 reference without documentation. Confirm the correct assembly drawing, equipment serial and supplied scope before purchase.
Start with the number and nameplate where they are available; then compare the machine, assembly and interfaces. If the record does not state a dimension, electrical value, supply scope or serial break, treat that information as unconfirmed and ask for it before order release.

| Order check | Current record | Evidence to confirm |
|---|---|---|
| Product | Shantui Bulldozer O-Ring 07000-63025 | Old-part label and equipment parts illustration |
| Reference | 07000-63025 | Nameplate, stamped mark or original-item label |
| Fitment | Shantui > Bulldozer parts category; exact model and serial range are not specified. | Machine model, serial and assembly version |
| Package scope | Catalog does not itemize accessories | Confirm each quantity and included item on the quotation |
Tie the O-ring to its groove
An O-ring is matched by its code, groove, cross-section, material and service conditions. A generic seal label does not provide these technical details.
No diameter, cross-section, compound or fluid range is listed. Similar ring names do not mean the same groove or interchangeability.
That distinction is important when equipment is maintained across more than one model year or configuration. A useful product page can explain what to compare, but it cannot replace the parts book for the exact serial range. Keep the inquiry tied to the machine that will receive the part; do not merge details from another unit merely because its name looks similar.
Keep nearby codes on separate lines
The fastest way to reduce back-and-forth is to send a compact evidence set with the first inquiry. Use the checklist below as a job-preparation step, and label each image with the component or position it shows.
An O-ring is matched by its code, groove, cross-section, material and service conditions. A generic seal label does not provide these technical details.
No diameter, cross-section, compound or fluid range is listed. Similar ring names do not mean the same groove or interchangeability.
Photograph the groove and mating faces before cleaning; keep the old ring with its location. Inspect the joint for scratches or contamination that could cause a leak independent of the seal.
Check the package code, ring profile and groove location without stretching the new seal. Follow the maker’s assembly method and use only specified lubricant.
Individually bag and label rings, protect from dust, sunlight and compression, and keep the printed reference with the work order.
State the requested quantity and whether the old item is available for side-by-side inspection.
Ask the supplier to list any unresolved fitment point directly on the quotation.
Confirm compound and dimensions from the correct source
Photograph the groove and mating faces before cleaning; keep the old ring with its location. Inspect the joint for scratches or contamination that could cause a leak independent of the seal.
When a part number is present, compare it character by character, including hyphens, suffixes and multiple references. When the number field is blank or contains an instruction to verify, do not turn that wording into a fabricated MPN. Use the equipment identification and physical evidence to establish the item, then keep the confirmation with the work order.
Dimensions can help, but they are meaningful only when the measuring points are clear. Record the unit, the point-to-point location and the orientation of the measurement. For electrical or hydraulic parts, a photo of the connector or port layout is not a substitute for the wiring or circuit diagram; it is supporting evidence for the technician and supplier.
Service notes for Shantui Bulldozer O-Ring 07000-63025
Request the verified size and compound against the assembly callout. Keep different codes separate in the quote and avoid using a stretched old ring as a measurement standard.
Separate observed symptoms from the suspected cause in the repair request. “Intermittent,” “leaking,” “slow” or “no response” describe what someone sees; they do not alone prove which component has failed. Preserve fault notes, inspection images and any test results that the technician considers appropriate. This makes a later inquiry easier to trace and helps prevent unnecessary repeat orders.
A quote scenario using 07000-63025
A practical enquiry for Shantui Bulldozer O-Ring 07000-63025 begins with the exact catalog line, equipment serial and a photograph of the installed item. This page is for 07000-63025, not the similar-looking 07000-63022 number on the adjacent catalog entry. Keep the two references on separate order lines unless the parts documentation explicitly says otherwise. Check the old seal position and the housing groove; visual similarity alone is not enough to establish material, dimensions or interchange. The quotation should state the confirmed reference and every included component.
This is an example of a verification workflow, not a reported customer case or a promise that the listed part will correct a fault. If the diagnosis changes after disassembly, update the parts request before shipment. If the component is part of a larger assembly, ask whether the supplier is quoting the complete assembly or only the identified subcomponent.
Receiving checks for Shantui Bulldozer O-Ring 07000-63025
Check the package code, ring profile and groove location without stretching the new seal. Follow the maker’s assembly method and use only specified lubricant.
Before installation, compare the supplied item with the written confirmation and approved service information. Keep machined, sealing, electrical or hydraulic interfaces protected until the work area is ready. Use the correct tools and procedures for the equipment; where a torque, pressure, calibration, clearance or adjustment value is not published in the record, obtain it from the proper technical source rather than estimating it.
Packing and traceability for this part
Individually bag and label rings, protect from dust, sunlight and compression, and keep the printed reference with the work order.
For a multi-item order, keep each component matched to its part number and work-order line. Small seals, clips, connectors or fittings should be individually identified if included. Photograph the carton labels and item markings at receiving, check quantities against the packing list, and document any transit damage before the part is mixed with workshop stock.
Related product references
The linked catalog entries can help compare adjacent service items, but a related page is not evidence of interchangeability. Confirm each application independently: O-ring 07000-63022; Seal ring 07018-11805.
Frequently asked questions
Are ring dimensions and material listed?
No. Obtain verified size and compound for this joint. For this record, the reference to retain is 07000-63025.
Can another O-ring with a similar appearance be used?
Not unless the drawing confirms the alternative. For this record, the reference to retain is 07000-63025.
What should be recorded before removing the old ring?
Its groove, direction and neighboring parts. For this record, the reference to retain is 07000-63025.
Does a leak prove this seal is the cause?
No. Inspect the full joint and follow the diagnostic procedure. For this record, the reference to retain is 07000-63025.
What to send for a confirmed quotation
Include the full machine model and serial, the complete engine or chassis plate where relevant, the product or old-part marking, clear photos of mounting and connection points, and any applicable diagram callout. State the quantity and required supply scope. If a number is missing, say so; a legible photo and a specific question are more useful than an invented part number. For cross-border shipments, also state the destination and the timing required for the maintenance plan.
Once the identity and scope are confirmed, keep the supplier’s written response with the order documents. That record helps the receiving team reconcile the item and gives the technician a clear basis for pre-installation checks.